Free CSS Templates

Digital Level Sensor (Supplied with a set of low, high and underground sensor, Fully Automatic with Pump Dry Run Protection)

Water Cartridge Filter

Specification:

	Diameter - 8”
	Height - 20”
Salient Features:
	No moving parts
	Leak proof tongue & groove body flange joint
	Designed for easy cartridge fixing & removal
	Both 'Absolute & nominal' rated cartridges
	Various cartridge options
	Out to In flow
	Completely closed system
	Housing as per pressure vessel design codes

Water Softener

Insulated Water Storage Tank

Specification:

	Capacity - 500 ltr*
	Size - 36”x30”x36”*
	Weight - 350 kgs
	Construction - Double walled.
	Insulation type - Thick PUF insulation all the sides
	Inner Tank - Thick gauge SS
	Outer Body - Laminated Sheet
	Inlet- ½ inch standard female thread connected to electronic Solenoid valve
	Outlet - 1 inch standard female thread with manual mechanical valve
	Overflow point - (½”)
	Micro control system for precise level sensing 2 electrodes technology (Fully computerized with 8 bit technology)
	Flooded Inlet water pressure required 1.5 k.g./c.m. sq.
Requirements for Installing the System:
	Maximum Load - 200 watts
	Power Input - Max 5 Amp- 230 V , 50 Hz, Single phase
	Water Inlet - Flooded with min 1.5 k.g./ c.m. sq - max 2.5 k.g./ c.m. sq, water quality - Clean, without sand/ dust particles
	Placement - at any secured place with electrical output and water output closer to it.
Note:
1.	If this system is installed at a lower level from where water is to be lifted to higher level, the outflow from the system should be achieved through the use of pressure system.
2.	Periodic cleaning of the tank could be achieved through the drain point.
3.	Drainage should be provided close to the installation.
4.	Overflow point should be connected to the drainage.
	(* - Other Capacity system could be customized)

Water Boiler

Water Chiller

Now you have respite from the hot temperatures. Campari offers storage water chillers in various capacities. You could add one for your shower and see the lifestyle soar with the luxury of a chilled pressurized shower.

This system can be installed conveniently and connected to the overhead tank anywhere.
Compatible pressure system recommended at the outlet line for your pleasure.

Model No. Capacity (Ltr.) K.W. Volts (V) Phase Fuse (Amp) Wire (mm) Size (lxbxh) ft Weight (Kgs) CL80 80 12 400 3 3X20 6.0 3.5'x2'x3' 150
Specifications:
	Construction – Double walled.
	Insulation type – Thick PUF insulation all the sides
	Inner Tank – Thick gauge SS
	Outer Body – Laminated Sheet
	Inlet- ½ inch standard female thread connected to electronic Solenoid valve with 60 mins shut off
	Outlet- 1 inch standard female thread with manual mechanical valve
	Overflow point – (½”)
	Flooded Inlet water pressure required 1.5 k.g./c.m. sq.
Salient Features:
	Made out of SS inner tank and thick laminated outer sheet
	PUF insulated
	Non Pressure efficient water chilling system
	Comes with active & passive safety system
	Micro controller based advanced system
	High on efficiency and performance

Water Semi Conditioner

Keeping in view the problems faced by the traditional water mixing technology and the acute temperatures, this system promises the best possible lifestyle for everyone. Now don’t torture your body anymore with water temperature variation. With powerful natural conditioning mechanism, this system also incorporates the electrical based marginal heating to eliminate the traditional mixers and conventional water heating systems. It’s easy placement behind the shower room itself makes it a more user friendly system with more viability for an improved LIFESTYLE.

This system is best suited for every home looking to improve their bathing beyond the normal ritual.

Specifications:
	Capacity – 80 ltr*
	Size – 24”x24”x40”*
	Weight – 150 kgs
	Construction – Double walled.
	Insulation type – Thick PUF insulation all the sides
	Inner Tank – Thick gauge SS
	Outer Body – Laminated Sheet
	Inlet- ½ inch standard female thread connected to electronic Solenoid valve with 60 mins shut off
	Outlet- 1 inch standard female thread with manual mechanical valve
	Overflow point – (½”)
	Flooded Inlet water pressure required 1.5 k.g./c.m. sq.
Salient Features:
	Equipped with natural conditioning system
	Equipped with its own pressurizing output with 3 bar pressure.
	Fast heating system
	Precise temp & level control
	Low water cut off
	Human Safe
	Low electricity consumption
	Micro control system for precise level sensing 2 electrodes technology (Fully computerized with 8 bit technology)
	Easy Installation system like any other geyser
	Easily serviceable and long life
	Non pressure system thus very safe to use.
	Could be operated on alternate power supply.
Requirements for Installing the System:
	Maximum Load - 4 K.W.
	Power Input – Max 20 Amp- 230 V , 50 Hz, Single phase
	Water Inlet – Flooded with min 1.5 k.g./ c.m. sq – max 2.5 k.g./ c.m. sq,
	water quality – Clean& Soft at max 100 PPM., without sand/ dust particles
	Placement – at any secured place with electrical output and water output closer to it.
Note:
1.	Now expensive mixers/ thermostatic mixers could be replaced with a normal single concealed valve, to operate the shower.
2.	The subdivided
3.	The water line from the pressure pump could also be extended to the washbasin and/or any other required point.
4.	Periodic cleaning of the tank could be achieved through the drain point.
5.	Drainage should be provided close to the installation for periodic cleaning.
6.	Overflow point should be connected to the drainage.
	(* - Other Capacity system could be customized)
	(** - Luxury range is also available, on request with more value addition)

Water Pure Conditioner

Keeping in view the problems faced by the traditional water mixing technology and the acute temperatures, this system promises the best possible lifestyle for everyone. Now don’t torture your body anymore with water temperature variation. With powerful electronic conditioning mechanism, this system also incorporates the electrical based marginal heating and chilling to eliminate the traditional mixers and conventional water heating systems and chillers. Its easy placement behind the shower room itself makes it a more user friendly system with more viability for an improved LIFESTYLE.

This system is best suited for every home looking to improve their bathing beyond the normal ritual.

Specifications:
	Capacity – 80 ltr*
	Size – 24”x24”x40”*
	Weight – 150 kgs
	Construction – Double walled.
	Insulation type – Thick PUF insulation all the sides
	Inner Tank – Thick gauge SS
	Outer Body – Laminated Sheet
	Inlet- ½ inch standard female thread connected to electronic Solenoid valve with 60 mins shut off
	Outlet- 1 inch standard female thread with manual mechanical valve
	Overflow point – (½”)
	Flooded Inlet water pressure required 1.5 k.g./c.m. sq.
Salient Features:
	Equipped with natural conditioning system
	Fast heating system
	Fast chilling system
	Precise temp & level control
	Low water cut off
	Human Safe
	Low electricity consumption
	Micro control system for precise level sensing 2 electrodes technology (Fully computerized with 8 bit technology)
	Easy Installation system like any other geyser
	Easily serviceable and long life
	Non pressure system thus very safe to use.
	Could be operated on alternate power supply.
Requirements for Installing the System:
	Maximum Load - 4 K.W.
	Power Input – Max 20 Amp- 230 V , 50 Hz, Single phase
	Water Inlet – Flooded with min 1.5 k.g./ c.m. sq – max 2.5 k.g./ c.m. sq,
	water quality – Clean& Soft at max 100 PPM., without sand/ dust particles
	Placement – at any secured place with electrical output and water output closer to it.

Water Pressure Pump

Ideal for boosting low water pressure automatically through tap operation. A pressure assembly is coupled to the pump. This system senses the differential pressure through opening/ closing the tap (manual valve).

Special features
Delivers Universal pressure irrespective of the floor
	Fully Automatic
	Easy installation
	Silent operation
1.	Up to 2 Bath Rooms (0.5 HP Pump & 8 Ltr Pressure Tank)
2.	Up to 4 Bath Rooms (1.0 HP Pump & 19 Ltr Pressure Tank)

In Line Water Heater/ Tank Less Water Heaters

In line water heater is a heat exchange device for in line water heating which is generally used to heat up the whirlpools/swim pools or a water reservoir where a particular temperature of water is to be maintained.. It becomes the best choice for an on line water heating application. Campari manufactures the best in its class in line water heaters. Its rugged heating coils and a thick gauge SS heat jacket with an inlet and outlet makes it most convenient equipment to use. It can also be installed for achieving an unending hot shower. Before installing this equipment, the client should understand that these are generally High kW heating systems and as such recommended to be used on 3 phase power supply system.

The in-line water heating systems comes duly equipped with a stem type thermostat, high heat cut out as part of standard safety measures.

The efficiency of the in-line water heater would purely depend upon the application. The efficiency could directly be monitored with the help of flow rate in liters per minute and the temperature difference at the inlet and outlet.

It’s fitment is quite easy. The inlet should be connected to the water source/ and the outlet may be connected to the hot water line or create a loop from the water reservoir